MAX30102 PULSE OXIMETER/HEART-RATE SENSOR MODULE I2C INTERFACE COM43

Fr8,600

The MAX30102 is an integrated pulse oximetry and heart-rate monitor biosensor module. It includes internal LEDs, photodetectors, optical elements, and low-noise electronics with ambient light rejection. The MAX30102 provides a complete system solution to ease the design-in process for mobile and wearable devices.

1 in stock

SKU: 10531SEN Category:

Description

The MAX30102 operates on a single 1.8V power supply and a separate 5.0V power supply for the internal LEDs. Communication is through a standard I2C-compatible interface. The module can be shut down through software with zero standby current, allowing the power rails to remain powered at all times.

Features 

  • Heart-Rate Monitor and Pulse Oximeter Biosensor in LED Reflective Solution
  • Tiny 5.6mm x 3.3mm x 1.55mm 14-Pin Optical Module
            Integrated Cover Glass for Optimal, Robust Performance
  • Ultra-Low Power Operation for Mobile Devices
            Programmable Sample Rate and LED Current for Power Savings
            Low-Power Heart-Rate Monitor (< 1mW)
            Ultra-Low Shutdown Current (0.7µA, typ)
  • Fast Data Output Capability
            High Sample Rates
  • Robust Motion Artifact Resilience
            High SNR
  • -40°C to +85°C Operating Temperature Range

Applications 

  • Fitness Assistant Devices
  • Wearable Devices

Getting started with the MAX30102 PULSE OXIMETER/HEART-RATE SENSOR MODULE I2C INTERFACE

The MAX30102 is an integrated pulse oximetry and heart-rate monitor biosensor module. It includes internal LEDs, photodetectors, optical elements, and low-noise electronics with ambient light rejection. The MAX30102 provides a complete system solution to ease the design-in process for mobile and wearable devices.

Step1: Hardware required

Step2: Connecting the Hardware

Step3: Setting up the library

ESP8266 ESP-12 NodeMCU WeMos D1 Mini WIFI 4M Bytes Development Board Module Library

1. Download and install the Arduino IDE on your operating system (some older versions won’t work).

2. Then, you need to install the ESP8266 add-on for the Arduino IDE.  For that, go to File > Preferences.

3. Enter http://arduino.esp8266.com/stable/package_esp8266com_index.json into the “Additional Board Manager URLs” field as shown in the figure below. Then, click the “OK” button.

4. Go to Tools > Board > Boards Manager

5. Scroll down, select the ESP8266 board menu and install “esp8266 platform”, as shown in the figure below.

MAX30102 Library

you can download it here  install the library by extracting that zipped file in the library folder as shown below

Step4: Upload the sample sketch

#include <Wire.h>
#include “MAX30105.h”

#include “heartRate.h”

MAX30105 particleSensor;

const byte RATE_SIZE = 4; //Increase this for more averaging. 4 is good.
byte rates[RATE_SIZE]; //Array of heart rates
byte rateSpot = 0;
long lastBeat = 0; //Time at which the last beat occurred

float beatsPerMinute;
int beatAvg;

void setup()
{
Serial.begin(115200);
Serial.println(“Initializing…”);

// Initialize sensor
if (!particleSensor.begin(Wire, I2C_SPEED_FAST)) //Use default I2C port, 400kHz speed
{
Serial.println(“MAX30105 was not found. Please check wiring/power. “);
while (1);
}
Serial.println(“Place your index finger on the sensor with steady pressure.”);

particleSensor.setup(); //Configure sensor with default settings
particleSensor.setPulseAmplitudeRed(0x0A); //Turn Red LED to low to indicate sensor is running
particleSensor.setPulseAmplitudeGreen(0); //Turn off Green LED
}

void loop()
{
long irValue = particleSensor.getIR();

if (checkForBeat(irValue) == true)
{
//We sensed a beat!
long delta = millis() – lastBeat;
lastBeat = millis();

beatsPerMinute = 60 / (delta / 1000.0);

if (beatsPerMinute < 255 && beatsPerMinute > 20)
{
rates[rateSpot++] = (byte)beatsPerMinute; //Store this reading in the array
rateSpot %= RATE_SIZE; //Wrap variable

//Take average of readings
beatAvg = 0;
for (byte x = 0 ; x < RATE_SIZE ; x++)
beatAvg += rates[x];
beatAvg /= RATE_SIZE;
}
}

Serial.print(“IR=”);
Serial.print(irValue);
Serial.print(“, BPM=”);
Serial.print(beatsPerMinute);
Serial.print(“, Avg BPM=”);
Serial.print(beatAvg);

if (irValue < 50000)
Serial.print(” No finger?”);

Serial.println();
}

Step5: Testing the circuit

Open the serial monitor – this is what I saw, it took a little bit of time for the readings to appear